This is the latest recevied telemetry packets stored in our database for station/object SP3ZBY-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1753754117 | 12 Count | 12 Count | 12 Count | 4 VDC | 0 VDC |
| 1753752317 | 1011 Count | 981 Count | 951 Count | 4 VDC | 0 VDC |
| 1753750516 | 998 Count | 969 Count | 939 Count | 4 VDC | 0 VDC |
| 1753748715 | 987 Count | 959 Count | 929 Count | 4 VDC | 0 VDC |
| 1753746914 | 974 Count | 947 Count | 917 Count | 4 VDC | 0 VDC |
| 1753745114 | 962 Count | 935 Count | 906 Count | 4 VDC | 0 VDC |
| 1753743313 | 950 Count | 924 Count | 895 Count | 4 VDC | 0 VDC |
| 1753741512 | 937 Count | 912 Count | 883 Count | 4 VDC | 0 VDC |
| 1753739712 | 922 Count | 898 Count | 869 Count | 4 VDC | 0 VDC |
| 1753737911 | 909 Count | 886 Count | 857 Count | 4 VDC | 0 VDC |
| 1753736110 | 896 Count | 874 Count | 845 Count | 4 VDC | 0 VDC |
| 1753734309 | 884 Count | 863 Count | 834 Count | 4 VDC | 0 VDC |
| 1753683950 | 642 Count | 631 Count | 603 Count | 3.99 VDC | 0 VDC |
| 1753680344 | 618 Count | 591 Count | 581 Count | 4 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)