K0FTT Automobiles

My position About ☰

reset

LZ0VRC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ0VRC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Humi*	Presaure*	Power*
1770087122	82.8 %RH	978 hPa	5.66 V
1770086822	82.8 %RH	978 hPa	5.64 V
1770086817	82.8 %RH	978 hPa	5.6 V
1770086522	82.8 %RH	978 hPa	5.65 V
1770086222	82.8 %RH	978 hPa	5.69 V
1770086217	82.8 %RH	978 hPa	5.68 V
1770085922	82.8 %RH	978 hPa	5.68 V
1770085622	82.8 %RH	978 hPa	5.62 V
1770085617	82.8 %RH	978 hPa	5.62 V
1770085322	82.8 %RH	978 hPa	5.61 V
1770085022	82.8 %RH	978 hPa	5.68 V
1770085017	82.8 %RH	978 hPa	5.68 V
1770084722	82.8 %RH	978 hPa	5.69 V
1770084422	82.8 %RH	978 hPa	5.6 V
1770084417	82.8 %RH	978 hPa	5.64 V
1770084122	82.8 %RH	978 hPa	5.68 V
1770083822	82.8 %RH	978 hPa	5.69 V
1770083817	82.8 %RH	977 hPa	5.61 V
1770083522	82.8 %RH	977 hPa	5.62 V
1770083222	82.8 %RH	977 hPa	5.62 V
1770083217	82.8 %RH	977 hPa	5.62 V
1770082922	82.8 %RH	978 hPa	5.68 V
1770082622	82.8 %RH	978 hPa	5.61 V
1770082617	82.8 %RH	978 hPa	5.61 V
1770082322	82.8 %RH	978 hPa	5.65 V

*Used Equation Coefficients:

Temp: 0, 0.01, 0

Humi: 0, 0.01, 0

Presaure: 0, 1, 0

Power: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)