K0FTT Automobiles

My position About ☰

reset

VK2RF-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RF-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Value1*	Value2*
1768695096	13.77 Volts	35.41 Deg.C
1768694955	14.01 Volts	33.94 Deg.C
1768694926	13.92 Volts	32.96 Deg.C
1768694851	14.33 Volts	32.48 Deg.C
1768694759	13.92 Volts	31.5 Deg.C
1768694636	14.21 Volts	30.52 Deg.C
1768694376	13.89 Volts	27.59 Deg.C
1768694348	14.06 Volts	26.12 Deg.C
1768694341	14.03 Volts	25.63 Deg.C
1768694331	14.21 Volts	25.14 Deg.C
1768694308	12.48 Volts	24.65 Deg.C
1768692498	13.92 Volts	32.48 Deg.C
1768692414	13.92 Volts	32.48 Deg.C
1768692401	14.18 Volts	32.48 Deg.C
1768692384	14.01 Volts	31.99 Deg.C
1768692374	13.86 Volts	31.99 Deg.C
1768692365	14.01 Volts	31.5 Deg.C
1768692335	13.8 Volts	31.01 Deg.C
1768692320	13.98 Volts	30.52 Deg.C
1768692163	14.01 Volts	29.05 Deg.C
1768692145	13.83 Volts	29.05 Deg.C
1768692102	13.92 Volts	28.56 Deg.C
1768692068	13.74 Volts	27.59 Deg.C
1768692033	13.51 Volts	26.61 Deg.C
1768681721	11.78 Volts	30.52 Deg.C

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)