K0FTT Automobiles

My position About ☰

reset

VK2LJ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2LJ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1764291784	13.27 Volts	24.65 Deg.C
1764291184	13.27 Volts	24.16 Deg.C
1764290285	13.27 Volts	23.67 Deg.C
1764289986	13.3 Volts	23.67 Deg.C
1764289386	13.27 Volts	23.18 Deg.C
1764289087	13.27 Volts	23.18 Deg.C
1764288787	13.27 Volts	22.7 Deg.C
1764288488	13.27 Volts	22.7 Deg.C
1764288188	13.27 Volts	22.7 Deg.C
1764287889	13.27 Volts	22.21 Deg.C
1764287589	13.27 Volts	22.21 Deg.C
1764287290	13.3 Volts	21.72 Deg.C
1764286990	13.3 Volts	21.72 Deg.C
1764286092	13.27 Volts	21.23 Deg.C
1764285792	13.27 Volts	21.23 Deg.C
1764285493	13.27 Volts	20.74 Deg.C
1764285193	13.27 Volts	21.23 Deg.C
1764284893	13.27 Volts	20.74 Deg.C
1764284594	13.27 Volts	20.74 Deg.C
1764284295	13.27 Volts	20.74 Deg.C
1764283995	13.3 Volts	20.25 Deg.C
1764283695	13.27 Volts	20.25 Deg.C
1764283096	13.3 Volts	19.76 Deg.C
1764282797	13.3 Volts	19.76 Deg.C
1764282497	13.27 Volts	19.76 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)