This is the latest recevied telemetry packets stored in our database for station/object W4KEL-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Value1* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1754079099 | 13.01 | 29.05 | 0 | 0 | 0 |
| 1754077302 | 12.98 | 30.03 | 0 | 0 | 0 |
| 1754075501 | 12.98 | 30.52 | 0 | 0 | 0 |
| 1754071903 | 13.01 | 31.01 | 0 | 0 | 0 |
| 1754068308 | 13.01 | 30.03 | 0 | 0 | 0 |
| 1754066506 | 13.01 | 27.59 | 0 | 0 | 0 |
| 1754064708 | 13.01 | 26.61 | 0 | 0 | 0 |
| 1754053918 | 13.01 | 26.12 | 0 | 0 | 0 |
| 1754052112 | 13.01 | 26.12 | 0 | 0 | 0 |
| 1754050314 | 13.01 | 25.63 | 0 | 0 | 0 |
| 1754048517 | 13.1 | 26.12 | 0 | 0 | 0 |
| 1754044927 | 13.01 | 26.12 | 0 | 0 | 0 |
| 1754043126 | 12.98 | 26.61 | 0 | 0 | 0 |
| 1754041332 | 12.98 | 26.61 | 0 | 0 | 0 |
| 1754039529 | 13.07 | 26.61 | 0 | 0 | 0 |
| 1754035932 | 13.01 | 27.1 | 0 | 0 | 0 |
| 1754032337 | 13.16 | 27.1 | 0 | 0 | 0 |
| 1754030537 | 13.04 | 27.1 | 0 | 0 | 0 |
| 1754028732 | 13.04 | 27.1 | 0 | 0 | 0 |
| 1754025134 | 12.98 | 27.59 | 0 | 0 | 0 |
| 1754023335 | 13.19 | 27.59 | 0 | 0 | 0 |
| 1754016139 | 13.04 | 29.05 | 0 | 0 | 0 |
| 1754010740 | 13.07 | 31.01 | 0 | 0 | 0 |
| 1754008941 | 12.98 | 32.48 | 0 | 0 | 0 |
| 1754007141 | 13.01 | 33.45 | 0 | 0 | 0 |
*Used Equation Coefficients:
Value1: 0, 0.0293, 0
Value2: 0, 0.489, -273.15
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)