K0FTT Automobiles

My position About ☰

reset

2E0XLS-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 2E0XLS-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1758094175	12.8 Volts	21.72 Deg.C
1758093994	12.8 Volts	21.72 Deg.C
1758093814	12.8 Volts	21.72 Deg.C
1758093454	12.8 Volts	21.72 Deg.C
1758093273	12.8 Volts	21.72 Deg.C
1758093093	12.8 Volts	21.72 Deg.C
1758092913	12.8 Volts	21.72 Deg.C
1758092371	12.8 Volts	21.72 Deg.C
1758092192	12.77 Volts	22.21 Deg.C
1758092011	12.77 Volts	22.21 Deg.C
1758091831	12.69 Volts	22.21 Deg.C
1758091650	12.54 Volts	22.21 Deg.C
1758091471	12.83 Volts	22.7 Deg.C
1758091290	12.8 Volts	22.7 Deg.C
1758091110	12.8 Volts	23.18 Deg.C
1758090929	12.8 Volts	22.7 Deg.C
1758090568	12.77 Volts	23.18 Deg.C
1758090388	12.8 Volts	23.67 Deg.C
1758090208	12.75 Volts	24.16 Deg.C
1758090027	12.63 Volts	24.65 Deg.C
1758089848	12.63 Volts	25.63 Deg.C
1758089666	12.66 Volts	27.1 Deg.C
1758089480	15.76 Volts	30.03 Deg.C
1758089411	15.35 Volts	27.59 Deg.C
1758089387	13.68 Volts	27.59 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)