K0FTT Automobiles

My position About ☰

reset

AI0ET-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI0ET-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vaux*	Vmain*	Pi_temp*
1762196760	12.42 Volts	0.01 Volts	36 Deg.C
1762196160	12.45 Volts	0.01 Volts	35 Deg.C
1762195561	12.49 Volts	0.01 Volts	34 Deg.C
1762193760	12.33 Volts	0.01 Volts	31 Deg.C
1762193160	12.34 Volts	0.01 Volts	32 Deg.C
1762191961	12.37 Volts	0.01 Volts	30 Deg.C
1762191361	12.39 Volts	0.02 Volts	29 Deg.C
1762190672	12.42 Volts	0.01 Volts	28 Deg.C
1762190072	12.49 Volts	0.01 Volts	27 Deg.C
1762189472	14.21 Volts	0.01 Volts	27 Deg.C
1762188873	14.11 Volts	0.01 Volts	28 Deg.C
1762188273	12.44 Volts	0.02 Volts	27 Deg.C
1762187672	12.7 Volts	0.01 Volts	27 Deg.C
1762187073	12.92 Volts	0.02 Volts	27 Deg.C
1762186842	11.95 Volts	0.01 Volts	30 Deg.C
1762186243	11.95 Volts	0.01 Volts	29 Deg.C
1762185642	11.95 Volts	0.01 Volts	28 Deg.C
1762185042	11.96 Volts	0.02 Volts	28 Deg.C
1762184442	11.96 Volts	0.01 Volts	27 Deg.C
1762183842	11.96 Volts	0.01 Volts	27 Deg.C
1762183242	11.96 Volts	0.01 Volts	26 Deg.C
1762182642	11.96 Volts	0.02 Volts	26 Deg.C
1762182042	11.97 Volts	0.02 Volts	25 Deg.C
1762181443	11.98 Volts	0.01 Volts	25 Deg.C
1762180842	11.95 Volts	0.01 Volts	25 Deg.C

*Used Equation Coefficients:

Vaux: 0, 0.01, 0

Vmain: 0, 0.01, 0

Pi_temp: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)