K0FTT Automobiles

My position About ☰

reset

4K6EH-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 4K6EH-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1783261037	903 Count	111 Count	48 Count
1783260133	902 Count	111 Count	48 Count
1783259230	901 Count	111 Count	48 Count
1783258326	900 Count	111 Count	48 Count
1783257506	899 Count	111 Count	48 Count
1783256603	898 Count	111 Count	48 Count
1783255699	897 Count	111 Count	48 Count
1783254796	896 Count	111 Count	48 Count
1783253892	895 Count	111 Count	48 Count
1783252989	894 Count	111 Count	48 Count
1783252085	893 Count	111 Count	48 Count
1783251182	892 Count	111 Count	48 Count
1783250278	891 Count	111 Count	48 Count
1783249375	890 Count	111 Count	48 Count
1783248472	889 Count	111 Count	48 Count
1783247568	888 Count	111 Count	48 Count
1783246665	887 Count	111 Count	48 Count
1783245761	886 Count	111 Count	48 Count
1783244858	885 Count	111 Count	48 Count
1783243954	884 Count	111 Count	48 Count
1783243051	883 Count	111 Count	48 Count
1783242147	882 Count	111 Count	48 Count
1783241244	881 Count	111 Count	48 Count
1783240340	880 Count	111 Count	48 Count
1783239436	879 Count	111 Count	48 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: