K0FTT Automobiles

My position About ☰

reset

PE1PNX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PE1PNX-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1788906648	823 Count	151 Count	145 Count
1788904844	822 Count	151 Count	145 Count
1788904602	817 Count	151 Count	145 Count
1788904049	812 Count	151 Count	145 Count
1788903524	807 Count	151 Count	145 Count
1788903125	802 Count	151 Count	145 Count
1788901321	801 Count	151 Count	145 Count
1788901288	797 Count	151 Count	145 Count
1788899484	796 Count	151 Count	145 Count
1788898587	791 Count	151 Count	145 Count
1788898420	786 Count	151 Count	145 Count
1788895513	781 Count	151 Count	145 Count
1788893840	776 Count	151 Count	145 Count
1788892037	775 Count	150 Count	145 Count
1788890233	774 Count	150 Count	145 Count
1788888429	773 Count	150 Count	145 Count
1788886626	772 Count	150 Count	145 Count
1788884822	771 Count	150 Count	145 Count
1788883018	770 Count	150 Count	145 Count
1788881215	769 Count	150 Count	145 Count
1788879411	768 Count	150 Count	145 Count
1788877649	763 Count	150 Count	145 Count
1788875845	762 Count	150 Count	145 Count
1788874041	761 Count	150 Count	145 Count
1788872238	760 Count	150 Count	145 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: