K0FTT Automobiles

My position About ☰

reset

SP3HUO-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP3HUO-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1774442940	663 Count	123 Count	104 Count
1774441138	657 Count	123 Count	104 Count
1774439337	649 Count	123 Count	104 Count
1774437536	643 Count	123 Count	104 Count
1774435735	638 Count	123 Count	104 Count
1774433933	633 Count	123 Count	104 Count
1774432132	628 Count	123 Count	104 Count
1774430331	623 Count	123 Count	104 Count
1774428530	618 Count	123 Count	104 Count
1774426728	613 Count	123 Count	104 Count
1774424926	607 Count	123 Count	104 Count
1774423125	602 Count	123 Count	104 Count
1774421324	584 Count	123 Count	104 Count
1774419550	576 Count	123 Count	104 Count
1774417749	571 Count	123 Count	104 Count
1774415948	548 Count	109 Count	90 Count
1774414147	543 Count	109 Count	90 Count
1774412346	538 Count	109 Count	90 Count
1774410545	533 Count	109 Count	90 Count
1774408743	528 Count	109 Count	90 Count
1774406942	522 Count	109 Count	90 Count
1774405141	517 Count	109 Count	90 Count
1774403340	513 Count	109 Count	90 Count
1774401539	508 Count	109 Count	90 Count
1774399738	503 Count	109 Count	90 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: