K0FTT Automobiles

My position About ☰

reset

SP2RO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2RO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	RX*	Digi*	V_Bat*
1762116975	20 Count	279 Count	3 Count	2.17 VDC
1762116074	16 Count	254 Count	0 Count	2.08 VDC
1762115174	15 Count	240 Count	0 Count	2.14 VDC
1762114273	14 Count	221 Count	0 Count	2.25 VDC
1762113372	13 Count	191 Count	0 Count	2.06 VDC
1762112471	12 Count	177 Count	0 Count	2.21 VDC
1762111571	11 Count	155 Count	0 Count	2.28 VDC
1762110670	10 Count	139 Count	0 Count	2.13 VDC
1762109769	9 Count	116 Count	0 Count	2.29 VDC
1762108868	7 Count	99 Count	0 Count	2.08 VDC
1762108005	3 Count	76 Count	0 Count	2.35 VDC
1762107105	2 Count	56 Count	0 Count	2.18 VDC
1762106204	1 Count	32 Count	0 Count	2.14 VDC
1762105303	0 Count	19 Count	0 Count	2.31 VDC
1762104402	56 Count	1006 Count	7 Count	2.25 VDC
1762103501	55 Count	992 Count	7 Count	2.21 VDC
1762102601	54 Count	966 Count	7 Count	2.16 VDC
1762101700	53 Count	949 Count	7 Count	2.15 VDC
1762100798	52 Count	934 Count	7 Count	2.32 VDC
1762099898	51 Count	921 Count	7 Count	2.28 VDC
1762098997	50 Count	896 Count	7 Count	2.22 VDC
1762098096	49 Count	883 Count	7 Count	2.2 VDC
1762097195	48 Count	858 Count	7 Count	2.18 VDC
1762096295	47 Count	849 Count	7 Count	2.2 VDC
1762095394	45 Count	830 Count	7 Count	2.33 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)