K0FTT Automobiles

My position About ☰

reset

VE7EOL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE7EOL-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Temp*
1768158542	13.89 Volts	16.34 Deg.C
1768158523	13.89 Volts	15.85 Deg.C
1768158518	14.09 Volts	15.85 Deg.C
1768158486	13.86 Volts	15.36 Deg.C
1768158392	13.83 Volts	13.89 Deg.C
1768158387	14.09 Volts	13.89 Deg.C
1768158373	14.18 Volts	13.4 Deg.C
1768158365	13.95 Volts	13.4 Deg.C
1768157741	14.06 Volts	11.45 Deg.C
1768157733	14.03 Volts	11.45 Deg.C
1768157728	13.86 Volts	11.45 Deg.C
1768157678	14.12 Volts	10.47 Deg.C
1768157668	14.24 Volts	10.47 Deg.C
1768157659	14.15 Volts	9.98 Deg.C
1768157642	14.09 Volts	9.98 Deg.C
1768157618	14.03 Volts	9.98 Deg.C
1768152145	14.01 Volts	7.54 Deg.C
1768152136	13.95 Volts	7.54 Deg.C
1768152111	13.68 Volts	7.05 Deg.C
1768152069	14.01 Volts	6.07 Deg.C
1768152032	13.89 Volts	5.58 Deg.C
1768152028	13.8 Volts	5.58 Deg.C
1768152001	13.71 Volts	5.58 Deg.C
1768151679	14.15 Volts	1.18 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)