K0FTT Automobiles

My position About ☰

reset

BG6STS-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BG6STS-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Sate*	Temp*	Pa*	Volt*
1755755924	7	42.4 C	994 hPa	13.11 V
1755755821	8	42 C	994 hPa	13.06 V
1755755771	7	41.9 C	994 hPa	12.73 V
1755755716	7	41.8 C	994 hPa	11.74 V
1755755613	6	41.5 C	995 hPa	11.66 V
1755755562	8	41.4 C	995 hPa	11.82 V
1755755511	9	41.1 C	995 hPa	11.71 V
1755755460	8	40.8 C	995 hPa	11.68 V
1755755152	6	39.9 C	996 hPa	11.74 V
1755754937	8	38.7 C	995 hPa	11.68 V
1755754886	7	38.2 C	995 hPa	11.68 V
1755754835	6	37.8 C	995 hPa	11.71 V
1755754784	7	37.5 C	994 hPa	11.71 V
1755754733	7	37 C	994 hPa	11.74 V
1755754681	7	36.6 C	994 hPa	11.63 V
1755754630	5	36.4 C	995 hPa	12.92 V
1755754579	6	36.1 C	995 hPa	11.66 V
1755754528	7	35.9 C	995 hPa	11.52 V
1755754426	5	35.6 C	995 hPa	11.9 V
1755754375	6	35.5 C	995 hPa	13.06 V
1755754324	2	35.3 C	995 hPa	13.42 V
1755743252	8	39.9 C	997 hPa	11.96 V
1755743201	8	39.7 C	997 hPa	11.96 V
1755743151	9	39.7 C	997 hPa	11.96 V
1755743099	9	39.8 C	997 hPa	11.99 V

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Pa: 0, 1, 0

Volt: 0, 0.01, 0

--: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)