K0FTT Automobiles

My position About ☰

reset

HK3Z-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HK3Z-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Sate*	Temp*	Pa*	Volt*
1768336071	11	39.5 C	748 hPa	9.32 V
1768335929	11	39.4 C	748 hPa	9.32 V
1768335854	11	39.4 C	748 hPa	9.32 V
1768335728	11	39.3 C	748 hPa	9.32 V
1768335634	11	39.3 C	748 hPa	9.26 V
1768335496	11	39.2 C	748 hPa	9.32 V
1768335342	11	39 C	747 hPa	9.29 V
1768335264	10	39.1 C	748 hPa	9.32 V
1768335101	8	39.1 C	748 hPa	9.32 V
1768335017	10	39.1 C	748 hPa	9.29 V
1768334943	10	39.1 C	748 hPa	9.29 V
1768334872	11	39 C	748 hPa	9.32 V
1768334769	11	38.9 C	748 hPa	9.26 V
1768334695	11	38.8 C	748 hPa	9.26 V
1768334620	9	38.8 C	748 hPa	9.32 V
1768334523	9	38.7 C	748 hPa	9.29 V
1768334416	10	38.6 C	748 hPa	9.32 V
1768334343	11	38.6 C	748 hPa	9.29 V
1768334269	10	38.6 C	748 hPa	9.32 V
1768334197	11	38.5 C	748 hPa	9.29 V
1768334125	10	38.6 C	748 hPa	9.29 V
1768334053	11	38.6 C	748 hPa	9.29 V
1768333981	11	38.6 C	748 hPa	9.29 V
1768333911	11	38.7 C	748 hPa	9.29 V
1768333839	10	38.8 C	748 hPa	9.29 V

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Pa: 0, 1, 0

Volt: 0, 0.01, 0

--: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)