K0FTT Automobiles

My position About ☰

reset

F5ZYM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F5ZYM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1792883045	166 Count	353 Count	111 Count
1792882141	165 Count	350 Count	111 Count
1792881237	164 Count	346 Count	111 Count
1792880333	163 Count	343 Count	111 Count
1792879429	162 Count	340 Count	111 Count
1792878525	161 Count	338 Count	111 Count
1792877621	160 Count	334 Count	111 Count
1792876717	159 Count	331 Count	111 Count
1792875813	158 Count	328 Count	111 Count
1792874909	157 Count	326 Count	111 Count
1792874004	156 Count	322 Count	111 Count
1792873100	155 Count	319 Count	111 Count
1792872195	154 Count	313 Count	111 Count
1792871291	153 Count	310 Count	111 Count
1792870387	152 Count	305 Count	111 Count
1792869483	151 Count	301 Count	111 Count
1792868579	150 Count	297 Count	111 Count
1792867675	149 Count	294 Count	111 Count
1792866771	148 Count	292 Count	111 Count
1792865964	147 Count	290 Count	111 Count
1792865060	146 Count	286 Count	111 Count
1792864156	145 Count	283 Count	111 Count
1792863252	144 Count	278 Count	111 Count
1792862348	143 Count	274 Count	111 Count
1792861444	142 Count	270 Count	111 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: