K0FTT Automobiles

My position About ☰

reset

KA6PRW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KA6PRW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	Temp*
1755711726	13.19 Volts	31.5 Deg.C
1755711698	13.33 Volts	31.01 Deg.C
1755711683	13.36 Volts	31.01 Deg.C
1755711668	13.36 Volts	31.01 Deg.C
1755711520	13.3 Volts	31.01 Deg.C
1755711397	13.39 Volts	31.01 Deg.C
1755711392	13.36 Volts	30.52 Deg.C
1755711299	13.39 Volts	30.52 Deg.C
1755711210	13.36 Volts	30.03 Deg.C
1755711022	13.3 Volts	29.54 Deg.C
1755711011	13.3 Volts	29.54 Deg.C
1755711006	13.39 Volts	30.52 Deg.C
1755710994	13.27 Volts	29.54 Deg.C
1755710989	13.21 Volts	29.54 Deg.C
1755710976	13.27 Volts	29.05 Deg.C
1755710833	13.3 Volts	28.56 Deg.C
1755710737	13.27 Volts	28.07 Deg.C
1755710533	13.3 Volts	25.63 Deg.C
1755710523	13.3 Volts	25.63 Deg.C
1755710510	13.27 Volts	25.14 Deg.C
1755710495	13.36 Volts	25.14 Deg.C
1755710455	13.36 Volts	24.65 Deg.C
1755710305	13.74 Volts	21.72 Deg.C
1755710204	13.71 Volts	19.76 Deg.C
1755700306	13.51 Volts	24.65 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)