This is the latest recevied telemetry packets stored in our database for station/object IZ1RFL-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1758622070 | 0 Count | 366 Count | 0 Count | 4.18 VDC | 0 VDC |
| 1758621170 | 0 Count | 345 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758620270 | 0 Count | 317 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758619370 | 0 Count | 294 Count | 0 Count | 4.18 VDC | 0 VDC |
| 1758618470 | 0 Count | 258 Count | 0 Count | 4.2 VDC | 0 VDC |
| 1758617570 | 0 Count | 236 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758616669 | 0 Count | 222 Count | 0 Count | 4.18 VDC | 0 VDC |
| 1758615769 | 0 Count | 197 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758614869 | 0 Count | 171 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758613969 | 0 Count | 150 Count | 0 Count | 4.21 VDC | 0 VDC |
| 1758613069 | 0 Count | 124 Count | 0 Count | 4.2 VDC | 0 VDC |
| 1758612169 | 0 Count | 102 Count | 0 Count | 4.2 VDC | 0 VDC |
| 1758611269 | 0 Count | 83 Count | 0 Count | 4.2 VDC | 0 VDC |
| 1758610369 | 0 Count | 62 Count | 0 Count | 4.17 VDC | 0 VDC |
| 1758610326 | 0 Count | 62 Count | 0 Count | 4.18 VDC | 0 VDC |
| 1758610319 | 0 Count | 62 Count | 0 Count | 4.18 VDC | 0 VDC |
| 1758610156 | 0 Count | 60 Count | 0 Count | 4.2 VDC | 0 VDC |
| 1758610151 | 0 Count | 60 Count | 0 Count | 4.18 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)