This is the latest recevied telemetry packets stored in our database for station/object KC3CNQ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | Value1* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1741988956 | 445 | 608 | 0 | 0 | 0 |
1741988359 | 438 | 603 | 0 | 0 | 0 |
1741985805 | 439 | 612 | 0 | 0 | 0 |
1741985685 | 438 | 612 | 0 | 0 | 0 |
1741985565 | 445 | 612 | 0 | 0 | 0 |
1741985446 | 445 | 612 | 0 | 0 | 0 |
1741985327 | 444 | 611 | 0 | 0 | 0 |
1741985207 | 444 | 611 | 0 | 0 | 0 |
1741985088 | 441 | 610 | 0 | 0 | 0 |
1741984968 | 441 | 609 | 0 | 0 | 0 |
1741984848 | 442 | 607 | 0 | 0 | 0 |
1741984609 | 420 | 602 | 0 | 0 | 0 |
1741982164 | 430 | 609 | 0 | 0 | 0 |
1741981805 | 439 | 606 | 0 | 0 | 0 |
1741981088 | 435 | 599 | 0 | 0 | 0 |
1741980746 | 449 | 592 | 0 | 0 | 0 |
1741980729 | 450 | 594 | 0 | 0 | 0 |
1741980610 | 449 | 592 | 0 | 0 | 0 |
1741973690 | 442 | 610 | 0 | 0 | 0 |
1741972136 | 443 | 595 | 0 | 0 | 0 |
1741972016 | 444 | 594 | 0 | 0 | 0 |
1741971897 | 443 | 593 | 0 | 0 | 0 |
1741971777 | 440 | 591 | 0 | 0 | 0 |
1741970940 | 442 | 581 | 0 | 0 | 0 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)