This is the latest recevied telemetry packets stored in our database for station/object SV2AHT-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1760017146 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760016246 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760015346 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760014446 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760013546 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760012646 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760011746 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760010846 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760009946 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760009045 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760008146 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760007245 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760006345 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760005445 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760004545 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760003645 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760002745 | 5.03 VDC | 0 | 0 | 0 | 0 |
1760001845 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760000945 | 5.04 VDC | 0 | 0 | 0 | 0 |
1760000045 | 5.03 VDC | 0 | 0 | 0 | 0 |
1759999145 | 5.03 VDC | 0 | 0 | 0 | 0 |
1759998244 | 5.04 VDC | 0 | 0 | 0 | 0 |
1759997344 | 5.03 VDC | 0 | 0 | 0 | 0 |
1759996444 | 5.03 VDC | 0 | 0 | 0 | 0 |
1759995544 | 5.04 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)