K0FTT Automobiles

My position About ☰

reset

DO5MF-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO5MF-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1768835590	102	5706	7552	2957	5195
1768834988	102	5697	7545	2966	5231
1768834384	102	5710	7545	2972	5270
1768833784	102	5706	7550	2977	5285
1768833182	102	5701	7547	2979	5294
1768832578	102	5711	7549	2981	5296
1768831978	102	5708	7547	2981	5294
1768831376	102	5704	7548	2979	5287
1768830775	102	5712	7549	2975	5278
1768830175	102	5710	7544	2970	5265
1768829573	102	5709	7544	2964	5245
1768828972	102	5709	7546	2957	5224
1768828372	102	5712	7548	2949	5199
1768827770	102	5708	7544	2939	5180
1768827169	102	5713	7545	2927	5168
1768826569	102	5711	7543	2915	5157
1768825967	102	5711	7544	2902	5140
1768825366	102	5715	7545	2886	5133
1768824766	102	5712	7546	2871	5139
1768824164	102	5706	7545	2854	5145
1768823564	102	5712	7543	2836	5158
1768822963	102	5714	7547	2823	5191
1768822362	102	5712	7543	2811	5247
1768821761	102	5713	7543	2798	5286
1768821160	102	5712	7543	2788	5288

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)