This is the latest recevied telemetry packets stored in our database for station/object DB0LPZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1761943315 | 4.18 VDC | 0 | 0 | 0 | 0 |
| 1761942415 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1761941515 | 4.08 VDC | 0 | 0 | 0 | 0 |
| 1761940615 | 4.07 VDC | 0 | 0 | 0 | 0 |
| 1761939715 | 4.11 VDC | 0 | 0 | 0 | 0 |
| 1761938815 | 4.08 VDC | 0 | 0 | 0 | 0 |
| 1761937915 | 4.15 VDC | 0 | 0 | 0 | 0 |
| 1761937015 | 4.14 VDC | 0 | 0 | 0 | 0 |
| 1761936114 | 4.11 VDC | 0 | 0 | 0 | 0 |
| 1761935214 | 4.17 VDC | 0 | 0 | 0 | 0 |
| 1761934314 | 4.08 VDC | 0 | 0 | 0 | 0 |
| 1761933414 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1761932514 | 4.12 VDC | 0 | 0 | 0 | 0 |
| 1761931614 | 4.08 VDC | 0 | 0 | 0 | 0 |
| 1761930714 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1761929813 | 4.07 VDC | 0 | 0 | 0 | 0 |
| 1761928913 | 4.18 VDC | 0 | 0 | 0 | 0 |
| 1761928013 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1761927113 | 4.11 VDC | 0 | 0 | 0 | 0 |
| 1761926213 | 4.08 VDC | 0 | 0 | 0 | 0 |
| 1761925313 | 4.07 VDC | 0 | 0 | 0 | 0 |
| 1761924413 | 4.18 VDC | 0 | 0 | 0 | 0 |
| 1761923513 | 4.17 VDC | 0 | 0 | 0 | 0 |
| 1761922613 | 4.1 VDC | 0 | 0 | 0 | 0 |
| 1761921713 | 4.1 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)