K0FTT Automobiles

My position About ☰

reset

SQ1BHQ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ1BHQ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1777376074	607 Count	106 Count	87 Count
1777374274	598 Count	106 Count	87 Count
1777372473	585 Count	104 Count	85 Count
1777370672	576 Count	102 Count	83 Count
1777368872	543 Count	82 Count	63 Count
1777367071	523 Count	72 Count	54 Count
1777365270	512 Count	72 Count	54 Count
1777363470	500 Count	72 Count	54 Count
1777361669	488 Count	72 Count	54 Count
1777359868	476 Count	72 Count	54 Count
1777358068	465 Count	72 Count	54 Count
1777356267	452 Count	72 Count	54 Count
1777354475	441 Count	72 Count	54 Count
1777352674	430 Count	72 Count	54 Count
1777350873	418 Count	67 Count	54 Count
1777349072	406 Count	66 Count	54 Count
1777347272	394 Count	66 Count	54 Count
1777345471	382 Count	59 Count	53 Count
1777343670	369 Count	56 Count	53 Count
1777341870	358 Count	56 Count	53 Count
1777340069	347 Count	56 Count	53 Count
1777338268	335 Count	56 Count	53 Count
1777336467	323 Count	56 Count	53 Count
1777334666	311 Count	55 Count	53 Count
1777332881	300 Count	55 Count	53 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: