K0FTT Automobiles

My position About ☰

reset

VK3XEM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK3XEM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1793650398	578 Count	152 Count	91 Count
1793649493	577 Count	152 Count	91 Count
1793648589	576 Count	152 Count	91 Count
1793647685	575 Count	151 Count	91 Count
1793646781	573 Count	150 Count	90 Count
1793645875	572 Count	150 Count	90 Count
1793644971	571 Count	150 Count	90 Count
1793644067	570 Count	149 Count	90 Count
1793643163	569 Count	149 Count	90 Count
1793642258	567 Count	147 Count	89 Count
1793641354	565 Count	145 Count	88 Count
1793640450	564 Count	145 Count	88 Count
1793639546	563 Count	145 Count	88 Count
1793638641	562 Count	145 Count	88 Count
1793637737	561 Count	144 Count	88 Count
1793636832	559 Count	142 Count	87 Count
1793635928	558 Count	142 Count	87 Count
1793635024	557 Count	142 Count	87 Count
1793634120	556 Count	142 Count	87 Count
1793633215	555 Count	142 Count	87 Count
1793632311	553 Count	141 Count	86 Count
1793631509	552 Count	141 Count	86 Count
1793630604	551 Count	141 Count	86 Count
1793629700	549 Count	140 Count	85 Count
1793628796	548 Count	140 Count	85 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: