K0FTT Automobiles

My position About ☰

reset

SQ9PQL-00 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9PQL-00. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1773443838	179 Count	165 Count	111 Count
1773442935	174 Count	150 Count	107 Count
1773442031	171 Count	146 Count	105 Count
1773441127	168 Count	143 Count	103 Count
1773440223	165 Count	140 Count	101 Count
1773439319	162 Count	137 Count	99 Count
1773438416	159 Count	134 Count	97 Count
1773437512	156 Count	131 Count	95 Count
1773436608	153 Count	128 Count	93 Count
1773435793	151 Count	127 Count	92 Count
1773434890	148 Count	124 Count	90 Count
1773433986	145 Count	121 Count	88 Count
1773433082	142 Count	118 Count	86 Count
1773432178	139 Count	115 Count	84 Count
1773431275	136 Count	112 Count	82 Count
1773430371	133 Count	109 Count	80 Count
1773429467	130 Count	106 Count	78 Count
1773428563	127 Count	104 Count	76 Count
1773427660	124 Count	101 Count	74 Count
1773426756	121 Count	98 Count	72 Count
1773425852	118 Count	96 Count	70 Count
1773424948	115 Count	94 Count	68 Count
1773424045	112 Count	91 Count	66 Count
1773423141	109 Count	88 Count	64 Count
1773422237	106 Count	85 Count	62 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: