K0FTT Automobiles

My position About ☰

reset

KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*	Chg*
1766028645	32 deg.F	11.35 V	10 V	2.54 Ah
1766028644	32 deg.F	11.35 V	10 V	2.54 Ah
1766027745	32 deg.F	11.45 V	10 V	2.54 Ah
1766026846	32 deg.F	11.5 V	10 V	2.54 Ah
1766026845	32 deg.F	11.5 V	10 V	2.54 Ah
1766025946	32 deg.F	11.55 V	10 V	2.54 Ah
1766025944	32 deg.F	11.55 V	10 V	2.54 Ah
1766025046	32 deg.F	11.6 V	10 V	2.54 Ah
1766025045	32 deg.F	11.6 V	10 V	2.54 Ah
1766024147	34 deg.F	11.65 V	10 V	2.54 Ah
1766024145	34 deg.F	11.65 V	10 V	2.54 Ah
1766023245	34 deg.F	11.7 V	10 V	2.54 Ah
1766023244	34 deg.F	11.7 V	10 V	2.54 Ah
1766022347	34 deg.F	11.75 V	10 V	2.54 Ah
1766022345	34 deg.F	11.75 V	10 V	2.54 Ah
1766021571	34 deg.F	11.75 V	10 V	2.54 Ah
1766021516	34 deg.F	11.8 V	10 V	2.54 Ah
1766021448	34 deg.F	11.75 V	10 V	2.54 Ah
1766021444	34 deg.F	11.75 V	10 V	2.54 Ah
1766020545	34 deg.F	11.8 V	10 V	2.54 Ah
1766020544	34 deg.F	11.8 V	10 V	2.54 Ah
1766019646	34 deg.F	11.85 V	10 V	2.54 Ah
1766019645	34 deg.F	11.85 V	10 V	2.54 Ah
1766018745	34 deg.F	11.9 V	10 V	2.54 Ah
1766018744	34 deg.F	11.9 V	10 V	2.54 Ah

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)