K0FTT Automobiles

My position About ☰

reset

SV3GCB-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SV3GCB-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1789682700	165 Count	152 Count	84 Count
1789681795	163 Count	150 Count	83 Count
1789680890	161 Count	148 Count	82 Count
1789679984	159 Count	146 Count	81 Count
1789679079	157 Count	144 Count	80 Count
1789678174	155 Count	142 Count	79 Count
1789677269	153 Count	140 Count	78 Count
1789676364	151 Count	138 Count	77 Count
1789675458	149 Count	136 Count	76 Count
1789673770	141 Count	133 Count	74 Count
1789672866	139 Count	131 Count	73 Count
1789671960	137 Count	129 Count	72 Count
1789671055	135 Count	127 Count	71 Count
1789670149	133 Count	125 Count	70 Count
1789669245	131 Count	123 Count	69 Count
1789668339	129 Count	121 Count	68 Count
1789667434	127 Count	119 Count	67 Count
1789666528	125 Count	117 Count	66 Count
1789665623	123 Count	115 Count	65 Count
1789664718	121 Count	113 Count	64 Count
1789663813	119 Count	111 Count	63 Count
1789662908	117 Count	109 Count	62 Count
1789662002	115 Count	107 Count	61 Count
1789661097	113 Count	105 Count	60 Count
1789660192	111 Count	103 Count	59 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: