K0FTT Automobiles

My position About ☰

reset

SP2RO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2RO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	RX*	Digi*	V_Bat*
1768851919	45 Count	240 Count	35 Count	0.94 VDC
1768851018	40 Count	212 Count	31 Count	0.96 VDC
1768850118	33 Count	177 Count	25 Count	0.94 VDC
1768849217	30 Count	155 Count	23 Count	0.93 VDC
1768848316	24 Count	122 Count	19 Count	0.93 VDC
1768847455	16 Count	88 Count	15 Count	0.86 VDC
1768846554	11 Count	49 Count	11 Count	0.97 VDC
1768845653	199 Count	1030 Count	177 Count	0.92 VDC
1768844752	184 Count	978 Count	163 Count	0.91 VDC
1768843851	178 Count	941 Count	158 Count	0.92 VDC
1768842950	172 Count	905 Count	153 Count	0.95 VDC
1768842050	167 Count	875 Count	149 Count	0.97 VDC
1768841149	161 Count	843 Count	144 Count	0.95 VDC
1768840248	156 Count	818 Count	140 Count	0.97 VDC
1768839347	150 Count	778 Count	135 Count	0.94 VDC
1768838446	145 Count	744 Count	131 Count	0.96 VDC
1768837545	139 Count	709 Count	126 Count	0.97 VDC
1768836644	118 Count	627 Count	106 Count	0.95 VDC
1768835744	94 Count	555 Count	83 Count	0.97 VDC
1768834843	77 Count	487 Count	67 Count	1.09 VDC
1768833942	67 Count	439 Count	58 Count	1.11 VDC
1768833041	64 Count	386 Count	56 Count	1.06 VDC
1768832140	59 Count	340 Count	52 Count	1.02 VDC
1768831239	50 Count	301 Count	44 Count	1.24 VDC
1768830339	44 Count	251 Count	39 Count	1.18 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)